Assam HS Skill Electrical Mechanics and Electrician exam-day guide
Assam HS Skill Electrical Mechanics and Electrician · Prepare for the day ahead.
Your checklist
Admit card / hall ticket (printed)
Carry the admit card issued for this practical examination. Keep a spare photocopy in a separate pocket from the original. The exact number of printed copies required is not fixed here - confirm with the provider.
Photo ID matching the admit card
Bring the original government photo ID whose details match your admit card and registration. A photocopy is usually not accepted as the primary ID - confirm with the provider which IDs are valid for your centre.
Passport-size photographs
Carry a few recent passport-size photographs in case the centre needs one for attendance or record sheets. The exact number and specification are not standardised - confirm with the provider.
Basic hand tools you are trained to use
Bring the tools you can confidently use: combination pliers, nose pliers, side cutters, screwdriver set, wire stripper, hammer, centre punch, try square, steel rule, and a measuring tape. Check the provider's list of permitted tools before packing; some centres supply tools instead of allowing your own - confirm with the provider.
Multimeter / test instruments (if permitted)
A working multimeter is commonly useful for continuity, voltage, and resistance checks. Whether you may bring your own or must use the centre's instrument is not fixed - confirm with the provider, and do not rely on a phone-based app.
Safety gear: safety shoes, goggles, gloves
Wear closed-toe safety shoes and carry safety goggles; insulated gloves are useful for any live testing. Do not wear loose sleeves, metal rings, watches, or dangling jewellery near rotating or live equipment.
Stationery and calculation aids
Pen, pencil, eraser, sharpener, and a simple non-programmable calculator if allowed. Whether calculators are permitted in the practical record work varies - confirm with the provider.
Prescribed dress / uniform and clean overalls
Many ITI and vocational centres expect the prescribed workshop uniform or overalls. The exact dress requirement for your centre is not standardised - confirm with the provider.
Reach the centre early and locate the workshop
Plan to arrive well before the reporting time, allowing for local transport delays. The reporting time and gate-closing rule are centre-specific - confirm with the provider rather than assuming a grace period.
Read the practical question paper and job drawing fully first
Before touching tools, read the whole job sheet, note the dimensions, tolerances, and the sequence of operations, and ask the invigilator only about unclear instructions, not about how to do the job.
Keep the workspace and record sheet organised
Lay out tools in a fixed order, keep the bench clear, and fill the observation/record columns as you complete each step so nothing is reconstructed from memory at the end.
Know the emergency and first-aid arrangements
Note where the first-aid box, fire extinguisher, and main switch/isolator are before starting. If you are unsure of the centre's emergency procedure, ask the invigilator at the start.
Plan the day
Re-read the admit card for reporting time, centre address, and any instructions on tools or dress. Confirm how you will travel to the centre and how long it takes, and arrange a backup route. Confirm with the provider any rule you are unsure about: permitted tools, calculator use, ID type, and uniform.
Practise the operations most likely to be assessed, at realistic speed: measuring and marking, stripping and terminating conductors, making sound joints, wiring a simple circuit (for example a one-way switch controlling a lamp with a socket), continuity and polarity testing, and reading a simple drawing. Practise safe isolation and proving dead before working on any circuit.
Inspect every tool: insulated handles free of cracks, pliers and cutters clean and free-moving, screwdriver tips not worn, hammer head secure on the handle. Test the multimeter on a known source and fit a fresh battery. Replace anything unsafe rather than carrying it.
Put the admit card, ID, and photographs in one folder. Keep a photocopy of the admit card separately. Check that the name and registration details on the admit card match your ID; if they do not, contact the provider immediately rather than on exam day.
Pack tools, safety shoes, goggles, gloves, stationery, admit card, ID, photographs, and water. Lay out the clothes you will wear. Do not leave packing to the morning.
Review safety rules, colour codes you have been taught, instrument usage, and the standard sequence for a job. Avoid learning new procedures the night before; sleep early so you are steady-handed for precision work.
Eat a proper meal; practical work is physical and long. Leave with enough margin to arrive ahead of the reporting time. Carry only what is permitted; leave valuables and phones at home or follow the centre's deposit rule.
Have the admit card and ID ready for verification. Follow the centre's instructions on where to wait and what may be carried into the workshop. If your name is not on the list or there is a document problem, speak to the centre authority at once.
Listen to the invigilator's instructions, read the question paper and drawing completely, identify the materials issued, and check that the tools and instruments you need are present and working. Note the total time and plan how long each operation will take, leaving time for testing and recording.
Work in a safe sequence: isolate and prove dead before touching any circuit, mark and measure before cutting, and keep the bench tidy. Follow the specified dimensions and tolerances. Do not copy from another candidate's job or borrow tools without the invigilator's knowledge.
Test your work with the instrument as instructed, record readings and observations as you go, and complete any viva or record-sheet entries. Before handing over, check that the job matches the drawing and that the workspace is left safe and clean.
If a tool breaks, an instrument fails, or you make an error, stop and inform the invigilator rather than improvising unsafely. Ask what replacement or extra time is allowed; that rule is centre-specific and must be confirmed with the provider.
Rules to check
Carry the original admit card and the original photo ID at all times in the centre; entry is normally refused without them, and the exact accepted ID types should be confirmed with the provider.
Follow the invigilator's instructions on which tools and materials may be brought in. Do not carry phones, smart watches, or unauthorised notes into the workshop; the deposit or confiscation rule is centre-specific - confirm with the provider.
Work only on the job and equipment assigned to you. Do not touch another candidate's circuit, tools, or machine, and do not help or seek help from other candidates during the test.
Treat safety as part of the assessment: wear the required safety gear, isolate circuits and prove dead before working, never bypass a safety device, and report any injury, shock, or damaged equipment to the invigilator immediately.
Ask the invigilator only for clarification of instructions or for replacement of defective tools or materials. Do not ask for guidance on method, dimensions, or answers.
Breaks, water, and toilet visits are usually at the invigilator's discretion and may be escorted; the centre's break policy and whether the clock stops are not standardised - confirm with the provider before the test.
Scoring is normally based on the completed job against the specified dimensions and tolerances, correct and safe working practice, correct use of instruments and testing, and the record/viva where applicable; the exact mark distribution and pass criteria should be confirmed with the provider.
Any suspected malpractice or unsafe act may lead to cancellation of the practical; if you believe an allegation is mistaken, stay calm and raise it through the centre authority rather than arguing at the bench.