NH Journeyman Plumber study materials
NH Journeyman Plumber study resources

NH Journeyman Plumber study plan

NH Journeyman Plumber · Give each week a clear focus.

8 weeks · About 7 hours per week

Week 1

Sanitary Drainage, Vents, and Storm Drainage & General Plumbing Knowledge

  • Build a one-page sizing worksheet for a residential DWV system that traces a 3-inch building drain from fixture to stack and labels every trap arm, branch interval, and vent connection

  • Calculate developed length for a horizontal branch and a vent using the 1/4-inch-per-foot slope rule, then verify the fall over the run in inches

  • Explain in writing the difference between a wet vent, a common vent, and an individual vent, and where each is permitted

  • Work 15 practice problems on trap arm length, slope, and fixture unit values, logging each miss with the code section that resolves it

Your checkpoint

Completed DWV sizing worksheet plus a 15-problem practice log with code citations for every missed item

Week 2

Sanitary Drainage, Vents, and Storm Drainage & General Plumbing Knowledge

  • Size a vent stack and a building drain using fixture unit tables for a two-bath dwelling and a small commercial restroom

  • Diagram a storm drainage system for a flat roof, showing roof drain sizing, leader sizing, and the difference between combined and separate storm systems

  • Identify the conditions that require a backwater valve, an air admittance valve, or a cleanout, and state the spacing and access rules for each

  • Solve 15 practice questions on venting and drainage, and rework every missed question until you can explain the correct answer without notes

Your checkpoint

Two sizing sheets (residential DWV and storm drainage) plus a 15-question practice set scored at 80 percent or better

Week 3

Water Supply and Distribution Systems & General Plumbing Knowledge

  • Size a water service and distribution main for a single-family home using demand-load and fixture-unit methods, and state the assumed pressure at the meter

  • Calculate pressure loss through a given length of pipe at a stated flow rate, and identify how elevation change affects residual pressure

  • Describe the purpose and placement of a pressure-reducing valve, a thermal expansion tank, and a backflow preventer in a residential system

  • Complete 15 practice problems on pipe sizing and pressure, correcting each error against a sizing table

Your checkpoint

Water supply sizing calculation packet with pressure-loss work shown for at least three pipe runs

Week 4

Plumbing Fixtures and Fixture Fittings & Water Heaters and Related Equipment

  • Match each common fixture (water closet, lavatory, sink, shower, floor drain) to its trap size, fixture-unit value, and minimum trap-to-vent distance

  • Explain the installation requirements for a water heater, including temperature and pressure relief valve discharge, drain pan sizing, and expansion control

  • Compare tank and tankless water heaters on venting category, combustion air, and clearance requirements, and state when each applies

  • Answer 20 practice questions on fixtures and water heaters, then rewrite any missed item as a short rule you can recall

Your checkpoint

Fixture and water heater reference card (one page, both sides) plus a 20-question practice set scored at 80 percent or better

Week 5

Fuel Gas Piping and Gas Appliances & General Plumbing Knowledge

  • Size a natural gas branch line for a range and a water heater using the longest-length and BTU tables, and show the pipe size at each segment

  • List the requirements for gas piping support, protection, shutoff valves, and sediment traps, and identify where each is required

  • Describe combustion air requirements for an appliance in a confined space and calculate the required free area for two openings

  • Complete 15 practice problems on gas sizing and appliance venting, citing the table or rule used for each answer

Your checkpoint

Gas piping sizing worksheet for a two-appliance system plus a 15-question practice set with citations

Week 6

New Hampshire Plumbing Code, Statutes, and Rules & General Plumbing Knowledge

  • Map the structure of the New Hampshire plumbing statutes and administrative rules: licensing, permitting, inspection, and enforcement authority

  • List the adoption and amendment points where the New Hampshire code differs from the model code, and note the practical effect of each

  • Explain the permit and inspection sequence for a residential remodel and for a new commercial buildout, including who may perform the work

  • Answer 20 practice questions on New Hampshire law and rules, and flag any item you cannot verify against the statute or rule text

Your checkpoint

New Hampshire code and statute outline (two pages) plus a 20-question practice set with a verified citation for each answer

Week 7

General Plumbing Knowledge & Sanitary Drainage, Vents, and Storm Drainage & Water Supply and Distribution Systems

  • Re-solve the three sizing sheets from weeks 1 through 3 from memory, then compare against the originals and correct discrepancies

  • Work a 40-question mixed set weighted toward drainage, venting, and water supply, and score it under timed conditions

  • Build a personal error list of the ten most repeated mistakes and write the correcting rule for each

  • Rehearse the code-section lookup path for the five topics you miss most often, timing each lookup

Your checkpoint

Timed 40-question mixed practice exam scored at 75 percent or better, with a written top-ten error list

Week 8

General Plumbing Knowledge & Plumbing Fixtures and Fixture Fittings & Water Heaters and Related Equipment & Water Supply and Distribution Systems & Sanitary Drainage, Vents, and Storm Drainage & Fuel Gas Piping and Gas Appliances & New Hampshire Plumbing Code, Statutes, and Rules

  • Take two full-length timed practice exams that mirror the domain weighting of the real exam and score each

  • Review every missed question and confirm the correct answer against the code text before moving on

  • Drill the New Hampshire-specific rules and the fixture and water heater card until recall is immediate

  • Write a one-page exam-day plan covering pacing per question, when to flag and skip, and how to handle calculation questions

Your checkpoint

Two completed full-length practice exams with a scored summary and a one-page exam-day plan

Milestones

Week 2: Can size a residential DWV system and a vent stack from fixture units without notes, and score 80 percent or better on a 15-question drainage and venting set

Week 4: Can state trap size, fixture-unit value, and water heater relief and venting requirements from the reference card, and score 80 percent or better on a 20-question fixtures and water heaters set

Week 6: Can outline the New Hampshire licensing, permitting, and inspection sequence and cite the statute or rule for each step, scoring 80 percent or better on a 20-question law and rules set

Week 8: Score 75 percent or better on both full-length timed practice exams, with no domain below 60 percent