I85PREP
⌘ K
AZ Asbestos Abatement study materials
AZ Asbestos Abatement study resources

AZ Asbestos Abatement practice questions

One question at a time. Build your AZ Asbestos Abatement understanding.

First 50 of 200 questions. Each one lists the choices, the correct answer, and an explanation. The checker at the top of this page saves progress in this browser when it is available.

Continue in the practice tool above to load more questions, 50 at a time.

Question 1Regulatory status and NESHAP applicability

Under the Asbestos NESHAP, which facility category is regulated for asbestos during demolition and renovation?

  1. Only schools and hospitals
  2. Institutional, commercial, and industrial facilities Correct answer.
  3. Only federal government buildings
  4. Only facilities built before 1980

Explanation

The Asbestos NESHAP applies to institutional, commercial, and industrial facilities, which includes most buildings other than certain residential structures. The rule keys on facility use and the amount of regulated asbestos-containing material involved, not on ownership or construction date.

Question 2Regulatory status and NESHAP applicability

A building owner plans demolition of a structure containing 300 linear feet of regulated asbestos-containing material on pipes. What must the owner do under the Asbestos NESHAP?

  1. Submit a written notice to the delegated agency before demolition begins Correct answer.
  2. Nothing, because linear feet do not count toward the threshold
  3. Wait until demolition starts and then report the material
  4. Only notify the local fire department

Explanation

Demolition of a facility that contains any regulated asbestos-containing material, including regulated pipe insulation measured in linear feet, requires advance written notice to the delegated agency. The notice must be submitted before work begins and must describe the material and the scheduled work.

Question 3Regulatory status and NESHAP applicability

How is regulated asbestos-containing material defined in the Asbestos NESHAP?

  1. Any material that contains more than one percent asbestos by weight
  2. Only sprayed-on fireproofing and thermal insulation
  3. Asbestos-containing material that is friable or will be made friable by the work Correct answer.
  4. Any material that contains any detectable asbestos at all

Explanation

Regulated asbestos-containing material is material that contains more than one percent asbestos and is friable, or will become friable during handling, demolition, or renovation. The category focuses on the potential for fiber release rather than simply the presence of asbestos.

Question 4Regulatory status and NESHAP applicability

A renovation will remove 200 square feet of regulated asbestos-containing material that is non-friable and will stay non-friable. How does the Asbestos NESHAP treat the project?

  1. The project is exempt because the quantity is below 260 linear feet
  2. The project is regulated because any removal is covered
  3. The project is exempt because the material remains non-friable Correct answer.
  4. The project is regulated only if the material is on pipes

Explanation

The renovation threshold is 160 square feet, 260 linear feet, or 35 cubic feet of regulated asbestos-containing material. Non-friable material that will remain non-friable is not regulated material, so it does not count toward that threshold.

Question 5Regulatory status and NESHAP applicability

Which agency is responsible for enforcing the Asbestos NESHAP at the federal level?

  1. The Department of Housing and Urban Development
  2. The Consumer Product Safety Commission
  3. The Occupational Safety and Health Administration
  4. The Environmental Protection Agency Correct answer.

Explanation

The Asbestos NESHAP is a Clean Air Act program administered and enforced federally by the Environmental Protection Agency. Some states and local agencies receive delegation to implement the program in place of the EPA.

Question 6Regulatory status and NESHAP applicability

Who is considered the owner of a facility for purposes of the Asbestos NESHAP?

  1. Any person who owns, leases, operates, controls, or supervises the facility Correct answer.
  2. Only the general contractor performing the work
  3. Only the party holding legal title to the property
  4. Only the lender holding the mortgage

Explanation

The rule defines owner or operator broadly to include anyone who owns, leases, operates, controls, or supervises the facility. This broad definition means more than one party can share NESHAP responsibilities.

Question 7Regulatory status and NESHAP applicability

A demolition project will remove a facility that contains no asbestos whatsoever. What notice obligation applies under the Asbestos NESHAP?

  1. Notice is required only if the building exceeds 10,000 square feet
  2. No NESHAP demolition notice is required Correct answer.
  3. Full written notice is still required before demolition
  4. Only a phone call to the agency is required

Explanation

Demolition notice is required when the facility contains regulated asbestos-containing material. If no asbestos is present, the NESHAP demolition notice requirement does not apply, although other permits may still be needed.

Question 8Regulatory status and NESHAP applicability

What does the term 'friable' mean when applied to asbestos-containing material?

  1. Material that is sealed behind a vapor barrier
  2. Material that can be crumbled, pulverized, or reduced to powder by hand pressure Correct answer.
  3. Material that contains less than one percent asbestos
  4. Material that has been painted or otherwise coated

Explanation

Friable describes material that can be crumbled, pulverized, or reduced to powder by hand pressure when dry. Friability matters because friable material is far more likely to release fibers into the air.

Question 9Regulatory status and NESHAP applicability

A renovation project will disturb 180 square feet of regulated asbestos-containing material. How is the project classified under the Asbestos NESHAP?

  1. It is a demolition rather than a renovation
  2. It is exempt because it is under 500 square feet
  3. It is a regulated renovation requiring notice and work practice compliance Correct answer.
  4. It is exempt because it is under 260 square feet

Explanation

A renovation is regulated when it disturbs at least 160 square feet, 260 linear feet, or 35 cubic feet of regulated asbestos-containing material. At 180 square feet, the project exceeds the square-foot threshold and must comply with notice and work practice requirements.

Question 10Regulatory status and NESHAP applicability

A contractor will remove 250 linear feet of regulated asbestos-containing pipe insulation during a renovation. What is the regulatory status of the project?

  1. It is exempt because the quantity is below the linear foot threshold Correct answer.
  2. It is exempt because linear footage is not counted in renovations
  3. It is regulated because it exceeds the 260 linear foot threshold
  4. It is regulated because it exceeds the 160 square foot threshold

Explanation

The linear-foot threshold for a regulated renovation is 260 linear feet of regulated asbestos-containing material. At 250 linear feet the project falls below that threshold, so it is not a regulated renovation on that basis alone.

Question 11Regulatory status and NESHAP applicability

When must an owner submit the NESHAP notification for a demolition that is ordered by a government agency because the structure is unsafe?

  1. Only after the demolition is complete
  2. Not at all, because emergency demolitions are always exempt
  3. As early as possible before demolition begins, with the required information Correct answer.
  4. Within 30 days after demolition begins

Explanation

Even for ordered demolitions, the owner must provide notice as early as possible before the work begins and include the required information. Notice is not eliminated by the emergency nature of the demolition, though timing may be compressed.

Question 12Regulatory status and NESHAP applicability

How many days before beginning a regulated renovation must the owner submit written notice to the delegated agency?

  1. At least 10 working days Correct answer.
  2. At least 45 calendar days
  3. At least 3 working days
  4. At least 20 working days

Explanation

For a regulated renovation, the owner must provide written notice at least 10 working days before the work begins. The notice allows the agency to schedule inspections and verify compliance.

Question 13Regulatory status and NESHAP applicability

An owner has already submitted a renovation notice but the start date changes. What should the owner do?

  1. Cancel the project entirely and start over
  2. Proceed on the new date without contacting the agency
  3. Submit a revised notice reflecting the new start date Correct answer.
  4. Wait for the agency to issue a new permit automatically

Explanation

When the scheduled start date changes, the owner should provide a revised notice so the agency has accurate information for inspection scheduling. Proceeding silently on a different date undermines the notice program.

Question 14Regulatory status and NESHAP applicability

Which materials are excluded from the definition of facility under the Asbestos NESHAP?

  1. Apartments and other residential buildings with four or fewer dwelling units Correct answer.
  2. Industrial manufacturing plants
  3. Commercial office buildings
  4. Schools and universities

Explanation

The definition of facility excludes residential buildings with four or fewer dwelling units and certain other structures. Schools, offices, and industrial plants are all covered institutional, commercial, or industrial facilities.

Question 15Regulatory status and NESHAP applicability

A building owner intends to demolish a structure and has determined that the only asbestos-containing material present is non-friable and will remain non-friable through demolition. What is the NESHAP obligation?

  1. Remove the material under a regulated renovation notice first
  2. Submit full demolition notice because asbestos is present
  3. Notify only the waste disposal site
  4. No demolition notice is required because no regulated material is present Correct answer.

Explanation

Demolition notice is triggered by the presence of regulated asbestos-containing material. Non-friable material that will remain non-friable is not regulated material, so the demolition notice requirement is not triggered on that basis.

Question 16Regulatory status and NESHAP applicability

What is the purpose of the NESHAP requirement to adequately wet regulated asbestos-containing material during stripping?

  1. To make the material easier to cut with power tools
  2. To satisfy local fire code requirements
  3. To increase the weight of the material for disposal billing
  4. To reduce the release of asbestos fibers into the air Correct answer.

Explanation

Wetting reduces fiber release by keeping asbestos dust bound to the material during handling. The work practice standards are designed to minimize visible emissions and airborne fiber concentrations.

Question 17Regulatory status and NESHAP applicability

A facility owner discovers that a renovation will disturb 35 cubic feet of regulated asbestos-containing material. How does this affect applicability?

  1. The project is exempt because cubic feet are not measured
  2. The project is regulated because it meets the cubic foot threshold Correct answer.
  3. The project is exempt because it is below 160 cubic feet
  4. The project is regulated only if the material is on a pipe

Explanation

The renovation thresholds are 160 square feet, 260 linear feet, or 35 cubic feet of regulated asbestos-containing material. Meeting any one of these thresholds makes the renovation regulated.

Question 18Regulatory status and NESHAP applicability

Which statement best describes how the Asbestos NESHAP and OSHA asbestos standards differ in focus?

  1. OSHA applies only to schools, while NESHAP applies to industry
  2. Both rules apply only to demolition contractors
  3. NESHAP controls air emissions to the environment, while OSHA protects worker exposure Correct answer.
  4. NESHAP protects workers, while OSHA controls ambient air quality

Explanation

The NESHAP is an environmental emission control program under the Clean Air Act, while OSHA standards address occupational exposure of workers. Both can apply to the same project, but they serve different statutory purposes.

Question 19Regulatory status and NESHAP applicability

An owner is unsure whether material in a building is regulated asbestos-containing material before a scheduled renovation. What is the most appropriate action?

  1. Assume it is not asbestos and proceed
  2. Rely on the building's age alone to decide
  3. Ask the demolition contractor to decide without testing
  4. Have the material sampled and analyzed by an accredited laboratory Correct answer.

Explanation

Applicability depends on whether material contains more than one percent asbestos and whether it is friable or will become friable. Sampling and analysis by an accredited laboratory provides the evidence needed to make that determination.

Question 20Regulatory status and NESHAP applicability

A renovation disturbs 100 square feet, 200 linear feet, and 10 cubic feet of regulated asbestos-containing material in separate components. How is applicability determined?

  1. The project is automatically regulated because multiple components are involved
  2. The measurements are added together and compared to 160
  3. Only the largest single measurement is compared to its threshold
  4. Each measurement is compared to its own threshold, and the project is exempt if none is met Correct answer.

Explanation

The rule sets separate thresholds of 160 square feet, 260 linear feet, and 35 cubic feet. Each quantity is compared with its corresponding threshold, and the renovation is regulated only if at least one threshold is met.

Question 21Regulatory status and NESHAP applicability

A structure will be demolished, and the only regulated asbestos-containing material is 30 cubic feet of Category I non-friable material that will be made friable by the demolition method. What is the correct conclusion?

  1. The demolition is regulated only if 160 square feet is also present
  2. The demolition is exempt because 30 cubic feet is below 35
  3. The demolition is exempt because Category I material is always excluded
  4. The demolition is regulated because the material will become friable Correct answer.

Explanation

Category I non-friable material becomes regulated material when it will be made friable by the work, and demolition of a facility with any regulated material triggers the notice requirement. The 35 cubic foot threshold applies to renovations, not to demolitions.

Question 22Regulatory status and NESHAP applicability

A contractor plans to use a mechanical chipping process on Category I non-friable roofing material during a renovation. How does this affect the material's regulatory status?

  1. The material remains non-friable regardless of the method used
  2. The material is regulated only if it exceeds 35 cubic feet
  3. The material becomes regulated because the method will make it friable Correct answer.
  4. The material is exempt because roofing is always excluded

Explanation

Non-friable material that will be made friable by the work method becomes regulated asbestos-containing material. Mechanical chipping can crumble or pulverize the material, so the friability analysis must account for the planned method.

Question 23Regulatory status and NESHAP applicability

An owner submits a demolition notice but later discovers additional regulated asbestos-containing material not described in the notice. What is the appropriate response?

  1. Proceed because the original notice was already filed
  2. Submit a revised notice with the updated information before work begins Correct answer.
  3. Wait until the material is removed and then report it
  4. Cancel the notice and rely on the contractor's judgment

Explanation

The notice must accurately describe the regulated material and the planned work. When new information changes the scope, the owner should revise the notice before work begins so the agency has a complete record.

Question 24Regulatory status and NESHAP applicability

A state has received delegation to implement the Asbestos NESHAP. Which program should an owner contact for notification and compliance questions?

  1. The state department of motor vehicles
  2. The delegated state or local agency Correct answer.
  3. Only the federal EPA regional office
  4. The nearest OSHA area office

Explanation

Where a state or local agency has been delegated authority, it implements the program and receives notifications. Owners should direct notices and questions to the delegated agency, although the EPA retains oversight.

Question 25Regulatory status and NESHAP applicability

An owner argues that a renovation is exempt because the regulated asbestos-containing material will be removed by hand rather than by machine. How should this argument be evaluated?

  1. It fails only if the material is on a pipe
  2. It succeeds if the material is wetted before removal
  3. It succeeds because hand removal never releases fibers
  4. It fails because the applicability thresholds do not depend on the removal method Correct answer.

Explanation

Whether a renovation is regulated depends on the quantity of regulated asbestos-containing material disturbed, not on whether the removal is manual or mechanical. Hand removal still requires compliance with notice and work practice standards once a threshold is met.

Question 26Regulatory status and NESHAP applicability

Which federal regulation establishes the Asbestos NESHAP requirements for demolition and renovation activities?

  1. 40 CFR Part 763, Subpart E
  2. 40 CFR Part 61, Subpart M Correct answer.
  3. 29 CFR Part 1910, Subpart Z
  4. 49 CFR Part 173, Subpart B

Explanation

The Asbestos NESHAP is codified at 40 CFR Part 61, Subpart M, which sets work practice standards and notification duties for demolition and renovation of facilities. Part 763 addresses asbestos in schools and accreditation programs, and Part 1910 is the OSHA general industry standard.

Question 27Regulatory status and NESHAP applicability

Under the Asbestos NESHAP, which agency is responsible for enforcing the demolition and renovation requirements when a state has not received delegation?

  1. The Occupational Safety and Health Administration
  2. The U.S. Environmental Protection Agency Correct answer.
  3. The local building inspector
  4. The state health department

Explanation

The NESHAP is a Clean Air Act program administered by EPA. Where a state has not been delegated authority, EPA's regional office receives notifications and enforces the standard directly. OSHA and local building departments enforce separate requirements.

Question 28Regulatory status and NESHAP applicability

Which term describes the owner or operator of a demolition or renovation activity under the Asbestos NESHAP?

  1. Any person who owns, leases, operates, controls, or supervises the facility or activity Correct answer.
  2. The lender holding the mortgage on the property
  3. The entity that holds title to the facility
  4. The general contractor performing the removal work

Explanation

The NESHAP definition of owner or operator is broad and covers any person who owns, leases, operates, controls, or supervises the source or activity. This means responsibility can rest with parties beyond the record title holder.

Question 29Regulatory status and NESHAP applicability

What does the acronym NESHAP stand for?

  1. National Emissions Survey for Health and Air Protection
  2. National Environmental Standards for Hazardous Asbestos Programs
  3. National Emission Standards for Hazardous Air Pollutants Correct answer.
  4. National Enforcement Standard for Hazardous Abatement Practices

Explanation

NESHAP refers to National Emission Standards for Hazardous Air Pollutants, issued under Section 112 of the Clean Air Act. Asbestos is one of the pollutants regulated by a NESHAP subpart.

Question 30Regulatory status and NESHAP applicability

An owner plans a renovation that will disturb exactly 160 square feet of regulated asbestos-containing material on facility components. How should the project be classified?

  1. As an exemption because the amount is below threshold
  2. As a demolition requiring notice
  3. As an unregulated minor project
  4. As a regulated renovation requiring notice Correct answer.

Explanation

A renovation is regulated when the amount of RACM to be stripped, removed, or disturbed is at least 160 square feet on facility components. Exactly 160 square feet meets the threshold, so the project is regulated and notice is required.

Question 31Regulatory status and NESHAP applicability

A renovation will disturb 80 linear feet of regulated asbestos-containing material on facility components and no other RACM. How is the project classified?

  1. Regulated, because linear measurements are always converted to area
  2. Unregulated, because only pipe insulation counts toward thresholds
  3. Unregulated, because the amount is below the linear threshold Correct answer.
  4. Regulated, because any linear footage triggers notice

Explanation

The regulated renovation threshold is 260 linear feet on facility components, in addition to the 160 square foot and 35 cubic foot thresholds. At 80 linear feet the project falls below the threshold and is not regulated on that basis alone.

Question 32Regulatory status and NESHAP applicability

An owner is planning a renovation and wants to know how the NESHAP treats material that is not friable and contains less than one percent asbestos. What is the regulatory status of that material?

  1. It is not asbestos-containing material under the NESHAP definition Correct answer.
  2. It is regulated RACM because any asbestos content triggers regulation
  3. It is Category II non-friable RACM
  4. It is regulated only if it will be sanded or ground

Explanation

The NESHAP defines asbestos-containing material as material containing more than one percent asbestos by weight. Material below that content threshold is not ACM and is not regulated under the standard, regardless of friability.

Question 33Regulatory status and NESHAP applicability

A facility owner is demolishing a structure and plans to remove all regulated asbestos-containing material before the wrecking begins. How does the NESHAP classify the project?

  1. As a demolition, because the structure itself will be wrecked Correct answer.
  2. As a minor project requiring no notice
  3. As a renovation only, because RACM is removed first
  4. As an exempt project, because no RACM remains at wrecking

Explanation

A demolition is the wrecking or removal of a facility, and the classification depends on the nature of the activity rather than on whether RACM is removed beforehand. Notice is still required for demolitions, including those where asbestos is removed prior to wrecking.

Question 34Regulatory status and NESHAP applicability

Which activity would be considered a renovation under the Asbestos NESHAP?

  1. Removing a load-bearing wall during interior remodeling of an office Correct answer.
  2. Taking down an entire manufacturing plant
  3. Wrecking a warehouse to clear a site
  4. Demolishing a residence destroyed by fire

Explanation

A renovation is the altering of a facility or its components, including the stripping or removal of RACM from components such as walls, pipes, and ductwork. Wrecking or removing an entire structure is a demolition.

Question 35Regulatory status and NESHAP applicability

An owner is preparing a NESHAP notification for a renovation and must describe the amount of RACM to be removed. Which measurement approach reflects the rule?

  1. Report only the single largest component measurement
  2. Report the total quantity on facility components in square feet, linear feet, or cubic feet as applicable Correct answer.
  3. Report the weight of all debris generated by the project
  4. Report the number of workers who will handle the material

Explanation

The NESHAP thresholds and notifications are expressed in terms of the amount of RACM on facility components, measured in square feet, linear feet, or cubic feet depending on the component. The total quantity to be disturbed governs whether the project is regulated.

Question 36Regulatory status and NESHAP applicability

A renovation project will disturb RACM in a facility that is a single-family residence used only for residential purposes. How does the NESHAP apply?

  1. The residence is regulated only if the owner occupies it
  2. The residence is regulated only if more than 260 linear feet is disturbed
  3. The residence is exempt from the NESHAP renovation requirements Correct answer.
  4. The residence is regulated because all buildings are covered

Explanation

The NESHAP definition of facility excludes certain structures, including single-family residences used for residential purposes, unless they are part of a larger installation. Such a residence is therefore outside the renovation and demolition requirements of the standard.

Question 37Regulatory status and NESHAP applicability

An owner of a regulated renovation submits notice but the work will now begin later than the date stated. What is the owner's obligation under the NESHAP?

  1. No action is needed because notice was already filed
  2. Submit a revised notice as soon as possible Correct answer.
  3. Cancel the original notice and wait 20 days
  4. Notify only the contractor, not the agency

Explanation

The NESHAP requires the owner to provide revised notice when information in the original notification changes, including the scheduled start date. The revised notice should be submitted as soon as possible so the agency has current information.

Question 38Regulatory status and NESHAP applicability

A contractor is removing Category I non-friable roofing material using a mechanical chipping process during a renovation. What is the regulatory status of this material under the NESHAP?

  1. It becomes regulated asbestos-containing material because the process may render it friable Correct answer.
  2. It becomes Category II non-friable material
  3. It is exempt because roofing material is never regulated
  4. It remains Category I non-friable and is unregulated

Explanation

Category I non-friable material that is subjected to sanding, grinding, cutting, or abrading is treated as RACM because the process can break the material down and release fibers. Mechanical chipping that crumbles or pulverizes the material can bring it within the regulated category.

Question 39Regulatory status and NESHAP applicability

An owner plans to demolish a structure in which the only RACM is Category I non-friable material that will remain undisturbed until the building is knocked down. How does the NESHAP treat the project?

  1. It is a demolition subject to the notice and work practice requirements Correct answer.
  2. It is exempt because Category I material is never counted
  3. It is a renovation because the material is not friable
  4. It is exempt because no RACM will be stripped

Explanation

A demolition of a facility that contains RACM, including Category I non-friable material that will be disturbed by the wrecking, is regulated. The owner must provide notice and comply with work practice standards even though no separate stripping occurs.

Question 40Regulatory status and NESHAP applicability

An owner is planning a renovation and is uncertain whether installed material is regulated asbestos-containing material. What does the NESHAP require before the project is classified?

  1. Assume all material is RACM and skip sampling
  2. Rely on the building's age alone to decide
  3. Have the material sampled and analyzed to determine asbestos content Correct answer.
  4. Ask the contractor to decide without documentation

Explanation

Proper classification depends on determining whether material contains more than one percent asbestos, which generally requires sampling and laboratory analysis by qualified personnel. Documentation of the determination supports the notification and compliance decisions.

Question 41Inspection and AHERA certification requirements

Under AHERA, which individual is responsible for ensuring that a school's asbestos management plan is implemented?

  1. The school's head custodian by default
  2. The regional EPA asbestos program manager
  3. The certified abatement contractor's supervisor
  4. The local education agency's designated person Correct answer.

Explanation

AHERA requires every local education agency to designate a person responsible for ensuring that the asbestos management plan is implemented and updated. That designated person coordinates inspections, reinspections, and recordkeeping duties. The role belongs to the LEA, not to contractors or regulators.

Question 42Inspection and AHERA certification requirements

How often must a local education agency conduct a reinspection of asbestos-containing building materials in its schools under AHERA?

  1. Every five years
  2. Every twelve months
  3. Every three years Correct answer.
  4. Every seven years

Explanation

AHERA requires reinspection of all known or assumed asbestos-containing building materials at least once every three years. The reinspection confirms condition and updates the management plan. Annual surveillance is a separate, more frequent activity.

Question 43Inspection and AHERA certification requirements

A school building constructed in 1985 contains vinyl floor tile that has never been sampled. Under AHERA, how should the LEA treat this material?

  1. Assume it is asbestos-containing until sampling proves otherwise Correct answer.
  2. Treat it as non-asbestos because the building predates 1986
  3. Remove it immediately regardless of condition
  4. Sample it only if a parent submits a written request

Explanation

AHERA requires that suspect materials in school buildings be either sampled and analyzed or assumed to contain asbestos. Assumed material is managed exactly like confirmed asbestos-containing material. The building's construction date does not exempt suspect materials from this rule.

Question 44Inspection and AHERA certification requirements

What is the minimum training requirement for an asbestos inspector under the federal Model Accreditation Plan?

  1. A three-day course with an examination Correct answer.
  2. A two-day management planner course
  3. A one-day awareness course
  4. A five-day contractor course

Explanation

The Model Accreditation Plan sets a three-day initial training course for inspectors, followed by a passing examination. Accreditation is discipline-specific, so inspector training differs from contractor or management planner training. Refresher training is required annually thereafter.

Question 45Inspection and AHERA certification requirements

A parent asks to review the school's asbestos management plan. What must the LEA do?

  1. Make the plan available for review without cost during normal business hours Correct answer.
  2. Refer the parent to the abatement contractor's records
  3. Provide a copy only after the parent pays copying fees in advance
  4. Require the parent to submit a formal discovery request

Explanation

AHERA requires the LEA to make the management plan available for inspection without cost during normal business hours. Copies must also be provided upon request, though reasonable copying charges may apply to copies. Access cannot be conditioned on formal legal process.

Question 46Inspection and AHERA certification requirements

Which of the following must be included in a school's asbestos management plan?

  1. A description of the location and condition of asbestos-containing material Correct answer.
  2. The manufacturer's warranty for the building roof
  3. A list of students with respiratory conditions
  4. The contractor's bid documents for future abatement projects

Explanation

The management plan must describe the location, amount, and condition of asbestos-containing building materials and outline response actions. It also includes inspection results and a plan for periodic surveillance. Bid documents and student medical records are not required elements.

Question 47Inspection and AHERA certification requirements

How frequently must a certified inspector complete refresher training to maintain accreditation?

  1. Annually Correct answer.
  2. Every five years
  3. Every two years
  4. Every three years

Explanation

Model Accreditation Plan disciplines, including inspector, require annual refresher training to keep accreditation current. The refresher course covers regulatory updates and review of inspection practice. Missing the annual refresher causes accreditation to lapse.

Question 48Inspection and AHERA certification requirements

Who is authorized to collect bulk samples of suspect asbestos-containing material in a school during an AHERA inspection?

  1. An accredited inspector Correct answer.
  2. A general maintenance worker
  3. A licensed electrician
  4. A school nurse

Explanation

Bulk sampling during an AHERA inspection must be performed by an accredited inspector following proper sampling protocols. Sampling requires training in safety, sample integrity, and documentation. Other trades lack the required accreditation.

Question 49Inspection and AHERA certification requirements

A school was inspected and the management plan was written in 2019. The LEA has not revisited the material since. What required activity has the LEA most likely missed?

  1. The five-year management plan rewrite
  2. The three-year reinspection Correct answer.
  3. The biennial EPA filing of sample results
  4. The annual refresher course for teachers

Explanation

Because the plan dates to 2019, a reinspection should have occurred within three years, and the LEA appears overdue. Reinspection confirms whether material condition has changed and whether the plan needs revision. Teachers do not take refresher courses, and no biennial EPA filing of sample results exists.

Question 50Inspection and AHERA certification requirements

During periodic surveillance, a custodian notices that previously intact pipe insulation has become damaged. What is the appropriate next step?

  1. Wait for the next three-year reinspection
  2. Notify the designated person so the management plan response action can be triggered Correct answer.
  3. Remove the insulation without notifying anyone
  4. Repair the insulation personally without documentation

Explanation

Periodic surveillance exists to detect changes in condition between reinspections. When damage is found, the observer must notify the designated person, who determines and documents the response action. Untrained staff should not disturb the material.