Part-66 Module 6 exam-day guide
Part-66 Module 6 · Prepare for the day ahead.
Your checklist
Valid photo ID
Bring the same identity document you used at registration (passport or national ID card). Confirm with the provider which forms of ID they accept and whether a second document is required.
Examination admission / booking confirmation
Printed or on-phone copy of your appointment confirmation, candidate number, or admission letter if your provider issues one. Check the exact arrival time and room on it.
Provider-approved calculator
Module 6 involves material properties, densities, and stress/load arithmetic. Confirm with the provider whether calculators are permitted and which models are banned (typically programmable or networked devices).
Nothing on your person that could be treated as unauthorised material
Leave notes, revision cards, smart watches, and phones in the locker or at home. Ask the invigilator where to store personal items before you sit down.
Stationery if allowed
Some centres supply everything; others allow only the pen/pencil they issue. Confirm with the provider whether you may bring pens, pencils, or an eraser.
Confirm the exam format and duration
Module 6 is normally a multiple-choice question paper delivered on paper or by computer. Confirm with the provider the number of questions, time allowed, and the pass mark before exam day so you can pace yourself.
Confirm the permitted reference material
Part-66 knowledge examinations are normally closed-book. Ask the provider explicitly whether any data sheets, formula sheets, or tables are supplied on the day.
Re-read your own summary of weak topics
One page only, reviewed the day before and then put away: material properties, corrosion types, fastener identification, and hardware marking conventions are the usual slip points in Module 6.
Plan the journey and arrive early
Aim to be at the centre well before the start time so that ID checks and seating do not eat into your exam time. Check local transport and parking in advance.
Know your provider's late-arrival and absence rules
Ask in advance what happens if you are delayed or fall ill, and whether a re-sit can be booked and at what cost.
Rest and eat sensibly beforehand
Avoid a last-minute cramming session the morning of the exam; a settled, alert candidate outperforms an exhausted one on recall-based multiple choice.
Read the candidate instructions sent by the provider
Providers issue a regulations or candidate handbook covering conduct, malpractice, and results. Read it in the final week rather than on the day.
Plan the day
Finish active revision: work through practice questions on materials, corrosion, fasteners, bearings, seals, and control cables. Stop learning new topics; consolidate what you already know.
Confirm the logistics: exact address, arrival time, room, ID requirements, and whether calculators or stationery are permitted. Contact the provider if anything is unclear.
Get three full nights of normal sleep. Do not trade sleep for extra revision in the last stretch.
Do one light review pass over your own summary sheet and the marking/identification conventions you find hardest. Then stop.
Prepare and lay out everything on the checklist: ID, confirmation, permitted calculator, transport tickets, and money for the journey.
Check travel plans against any disruption notices and set two alarms. Eat a normal meal and go to bed at your usual time.
Eat breakfast, avoid heavy caffeine if you are not used to it, and leave with enough margin to arrive early.
Do not open new material. At most, skim your one-page summary while travelling, then put it away before entering the centre.
Present your ID, store personal items as instructed, listen to the invigilator's briefing, and check that your question paper or workstation is the correct module and version before starting.
Read the candidate instructions on the paper or screen. Note the number of questions and the time allowed, and work out roughly how long you can spend on each.
First pass: answer everything you are confident about. Second pass: return to the harder items and eliminate options where possible. Leave nothing blank unless the marking scheme penalises wrong answers, which you should confirm in the instructions.
Watch the clock at the halfway point and near the end, and reserve a few minutes to check that every question has a recorded answer and your candidate details are correct.
Hand in all materials as instructed, collect your belongings, and note the provider's stated timescale and process for results and any re-sit.
Rules to check
Bring the identity document specified by your provider and keep it on the desk throughout; you will normally be refused entry without acceptable photo ID.
Follow the invigilator's instructions at all times, including on where to place bags, phones, and outer clothing, and on when you may leave your seat.
Treat the examination as closed-book unless the provider has confirmed otherwise in writing; possession of unauthorised notes or devices is normally treated as malpractice.
Raise your hand and wait for the invigilator if you need to leave the room, feel unwell, or have a problem with your paper or workstation. Confirm the provider's rules on toilet breaks, as escorted breaks may be allowed but the clock usually keeps running.
Do not communicate with other candidates once the examination has begun, and do not attempt to copy from or share answers with anyone.
Record an answer for every question unless the provider's instructions state that incorrect answers are penalised; confirm this before you start.
If you believe a question is defective, note the question number and report it to the invigilator after the examination rather than guessing at what was intended.
Confirm with your provider the pass mark, the number of questions, and the rules on re-sits and result appeals; these are set by the examining organisation and the competent authority, not by general assumption.