NICET ITFAS Level II study plan
NICET ITFAS Level II · Give each week a clear focus.
8 weeks · About 7 hours per week
Inspection and Testing of Fire Alarm Systems
Map the full ITFAS Level II task outline for inspection and testing into a personal checklist, tagging each task as known, shaky, or unknown
Define the difference between inspection, testing, and maintenance and state which NFPA 72 chapter governs each activity
List the documentation a tester must review before starting a job: record of completion, as-built drawings, manufacturer instructions, and prior test reports
Identify the tools and instruments needed for acceptance and periodic testing and describe what each measures
Your checkpoint
A one-page task checklist covering every inspection and testing task in the outline, with each item rated known, shaky, or unknown
Inspection and Testing of Fire Alarm Systems
Explain the sequence of a system acceptance test from plan review through final sign-off
Describe how to verify initiating device spacing, mounting height, and location against the standard and project drawings
Distinguish the test methods used for smoke detectors, heat detectors, duct detectors, and manual pull stations
State the pass/fail criteria and required documentation for each initiating device test
Your checkpoint
A written test-procedure sheet for all initiating device types with method, acceptance criteria, and documentation for each
Inspection and Testing of Fire Alarm Systems
Describe the test procedure for notification appliances including audibility, intelligibility, and visual coverage checks
Explain how to verify appliance circuit wiring, voltage drop, and supervision of notification circuits
Identify the correct test methods for speakers, strobes, and combination appliances and their acceptance criteria
Outline how to document notification appliance test results on the appropriate record forms
Your checkpoint
A completed sample notification appliance test record with method, measured results, and pass/fail for at least six appliance types
Inspection and Testing of Fire Alarm Systems
Explain primary and secondary power supply testing including battery load calculations and charger verification
Describe how to test the system under normal, standby, and alarm conditions and what to record
Identify the requirements for testing remote annunciators, communicators, and transmission paths
State the intervals and procedures for testing supervisory and trouble signals
Your checkpoint
A battery calculation worked end to end plus a power supply test log covering normal, standby, and alarm conditions
Inspection and Testing of Fire Alarm Systems
Describe the interface testing between the fire alarm system and suppression systems, HVAC, elevators, and door holders
Explain how to verify cause-and-effect matrix programming by triggering each input and observing each output
Identify the test methods for addressable system devices including device polling, mapping, and sensitivity verification
State the documentation required when interfaces fail or are deferred to another trade
Your checkpoint
A cause-and-effect verification matrix with at least fifteen input-output pairs, each marked tested and observed result
Inspection and Testing of Fire Alarm Systems
Explain the periodic inspection and testing intervals for each device and system component
Describe how to test and inspect waterflow and supervisory devices on sprinkler system interfaces
Identify the requirements for testing voice evacuation systems including message intelligibility and priority
Outline the process for handling impairments, including notification, fire watch, and documentation
Your checkpoint
A periodic inspection schedule table listing component, interval, test method, and documentation reference
Inspection and Testing of Fire Alarm Systems
Work through practice scenarios that require diagnosing a failed test and identifying the root cause
Explain how to evaluate whether a deficiency is a code violation, a design issue, or an installation defect
Describe the process for re-testing corrected deficiencies and updating records
Identify common documentation errors that cause acceptance test failures
Your checkpoint
Three written troubleshooting scenarios with diagnosis, corrective action, and re-test procedure for each
Inspection and Testing of Fire Alarm Systems
Review all weak areas flagged in earlier weeks and re-test knowledge on each
Complete a timed full-length practice set under exam conditions
Analyze missed questions by task area and close remaining gaps
Confirm readiness by scoring consistently above your target on two practice sets
Your checkpoint
A final gap analysis showing score by task area, with every previously flagged weak item resolved or scheduled for review
Milestones
Week 2: Can describe the full acceptance test sequence and the test method and pass criteria for every initiating device type without notes
Week 4: Can perform a battery calculation and explain normal, standby, and alarm condition testing from memory
Week 6: Can state the periodic test interval and method for every major component and explain the impairment process
Week 8: Scores at or above target on two timed practice sets with no task area below 70 percent